A much-needed lift for a… Vax Airlift

A Vax gets airlifted to safety

Back in the 1980s, VAX were famous for making bright orange, usually very robust, carpet washers. The products were premium priced at the time, and the sort of thing that ‘someone else had’. It was the sort of thing you borrowed when someone had spilled wine or worse on the floor in a last ditch attempt before condemning the carpet. I’ve only used one a few times, but I can remember that very distinct carpet shampoo smell.

Fast-forward to now and it seems that the VAX badge is owned by someone else and the name is applied to many vacuum cleaner designs. In my own recent experience, the products are a bit flimsy and parts are not easy to obtain. Indeed, on a recent repair, I tried and failed to get hold of a replacement motor for an 18-month-old machine only to be told by VAX that they don’t supply it, but that’s another story. Such a shame.

Anyway, on with a more positive story I think. The owner of this vacuum cleaner (not carpet washer) got in touch to tell me that they would like me to repair their VAX Airlift. As the name suggests, the machine is lightweight and slim, which makes lifting and manoeuvrability easier. However, lightweight in this case meant limited lifespan.

Make and model: VAX Airlift

Fault reported: Split hose

Cost of replacement machine: £200

Manufacturer support: 0/10

Cost of parts (for this repair): £1.00

My time spent on the repair: 1 hour

Tools needed: Screw drivers, pliers, cutters

Sundry items: None

Cleaning materials: Silicone spray, damp cloth

Repair difficulty: 3/10

Beverages: 1 X tea

Biscuits consumed: None, 1 slice of cheese on toast instead, must have been lunchtime

This model carries all dust sucking tools, brushes and other ‘extendibles’ onboard, for convenience. It’s neat and tidy and considering the amount of stuff onboard, it’s still amazingly light, hence the name. To be frank, I wish that I’d weighed it, but that might be going a bit far…

The problem with this machine was that the flexible hose from the brush head to the main machine had split. This caused air to rush into the hose’s hole when the vacuum was in use, which in turn meant that the vacuum simply wouldn’t suck up. The owner had attempted several previous repairs with electrical tape. These repairs had worked for a while, but after several hoovering sessions, the tape repair had failed and the machine was back to square one.

I took on the job and realised quite quickly that VAX’s sporadic spares listings on various websites neglected our poor friend and only certain consumables like filters were still available. Terrible really as the machine was only a few years old. The part I needed certainly wasn’t anywhere and looked unique to this model. When a situation like this confronts me, I do what any other sensible person does. Put the kettle on.

It’s often situations like this that will condemn a machine to waste, even when the rest of it is in serviceable condition. I can see why some may simply throw in the towel.

It soon dawned on me that I’d saved various bits of hose from old Dyson and Numatic vacuum cleaner repairs and that maybe something I’d salvaged might do the trick. That’s the power of a strong cup of Yorkshire Tea.

This was turning out to be my lucky day as some old grey Dyson vacuum hose that I’d salvaged from a knackered Dyson DC25 (if memory serves) looked like it would do the job.

The first task was to remove the bespoke Airlift connectors from the old hose and peel off the metres of horrible hairy electrical tape. Yuk. I needed the old hose, so that I could measure the correct length to allow a good fit in every position the machine would be used in. The hose end connectors were screwed on and bonded with impact adhesive, which just needed brute force to remove.

The Dyson hose was a gnats-whisker wider, but it still fitted the old hose connectors OK, with a little impact adhesive applied. The new-old hose with old connectors simply fitted back on the machine and I think you’ll agree, the new/old part looks like original equipment.

While I had the machine, I took the liberty to clean the seals, dust container and drive belts to the brush head as these were all clogged up. As filters were readily available, I also replaced these as they were only a few quid.

So, for small beans and using some old salvaged parts I already had, this VAX was ready to see another day. Most satisfactory.

DeLonghi Magnifica S Coffee Machine

Repair for small beans: A magnificent brew from the DeLonghi Magnifica S Coffee Machine

With more knobs and whistles than the Star Ship Enterprise, it’s no wonder that coffee machines like this have become very popular among coffee lovers. From the comfort of your own kitchen, you can brew-up in much the same way as a skilled barista in your local coffee shop does. With a machine like this, you will rarely ever make a mistake, since all measurements and mixes are made at the touch of a button. It’s a compelling package for the coffee nerd.

However, as we all know from school, the more complicated we make something, there’s an increased likelyhood of it going wrong at some point in the future.

I mean, they’re just so darn complicated. Don’t get me wrong, I admire the mechanical packaging and clever processes within these machines, but if just one small part of the mechanism goes wrong, the whole thing fails and the machine is then useless. And these things are not cheap.

The Magnifica S is a premium machine and Delonghi have been making these products for many years, so luckily, some parts are available for when things fall over. In my experience, DeLonghi coffee machines are of reasonable quality.

Make and model: DeLonghi Magnifica S (ECAM 22.110.SB)

Fault reported: Major leak

Cost of replacement: £330-400 when new

Manufacturer support:  5/10

Cost of parts: £1.50

My repair time: 2 hours

Tools needed: Small screwdrivers, small levers, cutters

Sundry items: Cable ties

Cleaning materials: WD-40, damp cloth, soap and water

Repair difficulty: 6/10

Cups of tea: x2

Cups of coffee: x1

Biscuits: Ginger nut x2

The owner of this machine used it everyday and upon delivering it to me for repair, was anxious to get it back soon for his daily caffeine hit as soon as possible.

I had to explain that my ‘shed hours’ are part-time and that I would do my best, but that I would make sure the (assuming I could fix it) it would be returned soon, as good as new. I know how to set myself up (eek).

Appliances like this have lots of ‘vanity’ panels, pieces of trim and general niceties that ‘clip in to place’ without a separate mechanical fixing like a screw. When dismantling, it’s often these parts which take the longest to remove since there are rarely any notes available out there. It’s often the lion’s share of the overall repair time. You just have to go slow and take things easy. That moment when a small plastic tang or lug goes snap is heartbreaking.

Luckily here, the DeLonghi designers had some foresight and the product came apart with care, albeit with some hairy moments.

A water leak had been reported to be coming from the front of the machine during operation. With so many pipes in the machine, the source of the leak could have been anywhere, but fortunately the cause was soon identified. A small silicone (high temperature) hose had ruptured from the boiler valve area to the milk frother wand. Although it wasn’t always in use on every occasion, the pipe’s rupture seemed to be causing a consistent leak with any coffee brew operation. All other areas of the machine seemed dry. With a Chinese original supplier of coffee machine silicone pipe on eBay coming to the rescue, the part I needed was delivered in a week for under £5.00. Result.

The old hose simply came off by temporarily unclipping the metal spring clips at each end. The new pipe simply clipped into place, with a little attention paid to length, so that no pinch-points occurred.

Back to my original point about ‘complication’. I’d ‘got away with it’ on this repair, there’s no getting away from it. A small silicone hose was an easy fix, with just the overall repair made complicated by the machine’s packaging.

If a valve or plastic water vessel had failed, I suspect that the repair wouldn’t have been possible. As another part-time hobby, I source repair items from all over the world (insert environmental case study here!) and it’s usually tricky to get parts like that, if they’re available at all. When repairing, I use a mix of second-hand, generic and original equipment to achieve a balance of quality, cost-effectiveness and minimal environmental damage. It’s not easy. The problem for repair agents is that it takes time to work all of that out before the repair begins…it’s a constant dilema and blog article for another day.

When doing a job like this, it makes sense to make sure that all things that can’t be cleaned easily when assembled are inspected and washed as required.

The coffee group head was one such item. While it is possible to service this item with the machine fully assembled, it’s easier to clean it when it isn’t. I hope that the owner noticed a boost in coffee strength as many of the small water holes in the group head were blocked. Of course, I made sure that everything else was ship-shape too before reassembly.

After reattaching all of the appliance’s panels, it was time to give the machine a portable appliance test (PAT) and brew-up. A sucessful repair for small beans.

Genuine or pattern parts? A Dyson DC40 gets a little tune-up.

Genuine or pattern parts? What to do!?

Article 100!

It’s a dilemma sometimes.  Should you always fit genuine replacement parts or is it OK to fit quality aftermarket or pattern parts.  My answer:  It depends.

Make and model: Dyson DC40

Fault reported: Torn hose and loss of suction

Cost of replacement: About £200.00

Cost of parts: £16.53 (hose and filters)

Hours spent on repair: 1

Tools needed: Screwdrivers

Sundry items: Silicone spray, PTFE spray, rag

Repair difficulty: 2/10

Cups of tea: 2

Biscuits: 1 McVities Gold Bar

A mate of mine contacted me to ask if it was worth fixing his 6 year old Dyson DC40 and as always, I said yes it was.  A couple of days later, it was working again, like new.

IMG_0446
FixItWorkshop, November’19, Dyson DC40.

The DC40 is still supported by Dyson and parts are readily available direct from them.  Problem is that, as my mate did, the price of some spares (although quite reasonable actually) can put some people off, which means that serviceable machinery can end up at the local dump, prematurely.  Which is a shame.

This is where pattern parts can help.  Often, aftermarket manufacturers will make spares for popular models and the advantage of these is that they are often much cheaper than the original part.  However, it’s not as simple as that.

I’ve fixed 100s if not 1000s of things and have used and continue to use a mixture of genuine original (often called OE or Original Equipment) and pattern parts for different reasons.  Assuming original equipment parts are the best, here are my thoughts, in no particular order, to help you if facing a similar dilemma.

In favour of pattern parts:

  • They can make a repair viable, financially
  • Parts can be available, long after original parts become obsolete
  • They can provide enhanced features that were not part of the original design

In favour of genuine/ original equipment parts:

  • They will fit exactly as the specification will be to the original design
  • They maintain manufacturers warranties, where applicable
  • They normally last well and perform as expected

As a further example, I will only fit genuine water pumps (on car engines) but will fit pattern air filters.  Water pumps must work within very exact performance tolerances whereas air filters, although important, don’t so much.  It’s a personal thing at the end of the day.

Back to the repair.  This Dyson wasn’t picking up dirt and the extension hose was torn, so a new hose was ordered from a supplier on eBay for under £10, a genuine part was over £25.  The hose just clicks out and in, so all that was required was a small flat bladed screwdriver to remove and refit the hose.  Nice and easy.

The next job was to sort out the lack of suction.  As with all Dysons with a problem like this, I always check filters.  As suspected, both filters were expired and needed to be replaced as they were too far gone to be washed.  Again, pattern part filters were available on eBay for under £7, genuine ones were much dearer.  All new parts fitted well and soon the vacuum cleaner was breathing easily again.

Another issue with the DC40 is the switch lever which diverts suction from the beater head to the hose, which was sticking on this machine.  A quick clean up and a small spray of silicone spray on all the moving parts had it all working again.

This slideshow requires JavaScript.

I always clean-up the beaters on any vacuum cleaner in for a service and this one seemed to have half a head of hair stuck in it, which would have impeded performance.  The hair was so bad, I had to remove the beaters (just one screw) and cut off the hair with a knife.

With all the remedial work completed, the Dyson ran well proving once again that it’s usually worth repairing, rather than replacing.

 

Dyson DC14 with no vacuum

Another Dyson repair…

As covered a few times on my blog already, I do like Dyson products.  They’re engineer and tinker-friendly.

IMG_8360
Fixitworkshop, March’19, Dyson DC14 (PS, I did clean the old paint off later).

A colleague got in touch with a poorly DC14 which had worked well.  She’d kept the filters clean and generally looked after the appliance with care, which makes a nice change. However, despite all this, nothing was being collected with the floor beaters.  The hose worked OK, but that was it.

Time to do some screwdriver wealding.  Despite the filters being in good condition, I washed and dried them anyway, just in case.

Up ending the vacuum cleaner revealed the problem straight away.  The bottom foot hose had become disconnected from the interference fit compression joint and was flapping in the breeze.  Usually when this happens, it’s because the hose has split, but this one was in good condition.  What seemed to have happened was that the hose had become untwisted from the joint, so all that was required was careful reassembly.

While the cleaner was in pieces, I gave it a thorough service, paying attention to all of the machine’s seals and moving parts, especially where the cylinder joins the vacuum pipes from the motor as these can leak with age.

Once spruced-up, the cleaner was back to full health once again.  Another Dyson saved from the tip.

This slideshow requires JavaScript.

Cost of replacement:  £150 and up.  Cost of repair: Time, tea and biscuits and silicone spray, a bit of washing-up liquid.