Wheezy Dyson DC19

Another Dyson not biting the dust, just yet.

A mate asked if it was worth saving his abused Dyson cylinder vacuum cleaner which has been residing in the garage for a couple of years, in the dark, unused. It had last seen service when clearing-up building dust and allsorts of non-domestic detritus and that abuse had now given the vacuum cleaner breathing difficulties. A vacuum with breathing issues means no suction.

IMG_0937
FixItWorkshop, Worthing, January 2020, Dyson DC19.

Interestingly, the reason the Dyson was being called out of retirement was due to a lack of performance from the family’s more recently purchased battery machine. Hopefully I’ll get to see that in the workshop soon as well. I’m getting ahead of myself already.

Make and model: Dyson DC19 (grey and purple)

Fault reported: 70% reduction in suck

Cost of replacement: About £200

Cost of parts: £9.54

Hours spent on repair: 1

Tools needed: Cleaning tools

Sundry items: Silicone spray

Repair difficulty: 1/10

Cups of tea: 1

Biscuits: 2 (M&S Belgium Selection)

This slideshow requires JavaScript.

Like many abandoned vacuum cleaners I see in the workshop or at the tip, there really wasn’t much wrong or really broken, yet its owner was considering its future. What to do. I’ll write about readiness to repair and repair inertia another time!

The repair in stages:

  • Remove, clean (and replace) filters and refit once dry (48 hours)
  • Remove collection cylinder and clean thoroughly and refit once dry (48 hours)
  • Clean all seals with soap and water, dress with silicone to revive
  • Check by-pass valve and clean as needed
  • Check power cable (clean to improve flex rewind system)
  • Check and clean roller brush head
  • Test!

The filters on this machine were so dirty that I decided to invest in a new set which, at under £10, seemed good value and will certainly extend the life of the DC19.

After giving the main unit a good polish the Dyson DC19 was ready to go home to clean-up. Another Dyson not biting the dust, just yet.

Nearly flaming 1986 Yamaha XT600 Ténéré

Beloved Yamaha XT600 Ténéré nearly goes up in smoke.

I’ve had my beloved Yamaha XT600 Ténéré for about 8 years and have deliberately kept it away from these pages as I’m always doing something to it.  It could have its own website with the amount of time, not to mention money and effort I’ve spent on it.

IMG_20180128_141128
FixItWorkshop, Jan’18, Yamaha XT600 Ténéré.

This story is note-worthy as it’s a lesson for me and others who ride and maintain old bikes!

I don’t use the bike that much at the moment, but I always keep it ready for the road, just in case I get a chance to take it out.  Whilst doing a few checks recently, I decided to fire it up and get the oil pumping around the engine, so that things don’t seize up.

The tank was pretty full (over 20 litres) and upon opening up the manual fuel valves, giving it a bit of choke, the engine fired-up on the second crank.  It sounded quite sweet.

However, after about 30 seconds, I heard ‘running liquid’ before smelling the intense scent of super unleaded.  Looking down, I was standing in about 2 pints of fuel, on the wooden shed floor with a hot exhaust casually burning the fuel that was dripping on to it.  Nasty.

I won’t repeat what I said, but suffice to say, I hit the bikes’ kill switch virtually instantly.  I shut the flowing fuel off and wheeled the bike out in to the open air.

After several cups of tea, I found the cause of the problem.  The small fuel feed pipe which runs from the float chamber to the main jet on the carburettor had failed causing the leak.

When I bought the bike, I thought I’d changed all the fuel lines, but I’d missed one, quite an important one as it turned out.  It goes to show that even enthusiastic mechanics make mistakes.

The cost of the repair was £1 for a new piece of fuel hose, but the point of this story is:  If you have any petrol-powered things, especially old motorbikes; don’t run them in an enclosed wooden space.  Always run them outside.