Kaput Bosch AL1450DV Drill Battery Charger

An old Bosch battery charger gets a new lease of life.

These chargers often lead a hard life, working in dusty, hot and noisy conditions, so I guess many of these fail in time.

This Bosch unit is fairly common among Bosch DIY drill sets and this one had died catastrophically.  With the power applied, this one refused to give the slightest charge to a drill battery, once plugged in.

After some basic testing, I decided to change four components which would have caused the other to fail in a ‘domino effect’.  The cost of the replacement parts was just shy of £10, but definitely worth saving since second-hand units seemed to be changing hands for £40 on eBay, with their condition largely unknown.  The parts (two resistors, MOSFET transistor and diode/ transistor) were readily available online.

I recorded a short video to help others who might have a similar problem with theirs…

 

Pump, ready for the dump

This asthmatic car tyre pump came in to the workshop with little going for it.  The owner had been very close to throwing it away when he came across my website.

This AirMan pump is designed to be plugged in to a car’s cigarette lighter socket and provide quick and convenient car tyre inflation.  This one was dead.

On first inspection, the fuse was OK, the switch seemed to work and all connections seemed sound, when tested with a multi-meter.

IMG_3604.JPG
FixItWorkshop, Worthing, May’17 AirMan Car Tyre Pump, repaired

Off with the cover…

IMG_3598.JPG
FixItWorkshop, Worthing, May’17 AirMan Car Tyre Pump, repaired- cover removed

When the motor was removed from the cam driving the piston, the bit that drives the pump, it spun freely when power was applied, using a battery in the workshop.

IMG_3588.JPG
FixItWorkshop, Worthing, May’17 AirMan Car Tyre Pump, repaired- gear wheel

Seemingly, the centre spindle was protruding far beyond it’s specified reach, causing the pump connection rod to it it during rotation.  Why?  To be frank, I wasn’t sure. I can only surmise that the vibration and heat had caused the flywheel/ toothed drive to slide outside of specification.

IMG_3596.JPG
FixItWorkshop, Worthing, May’17 AirMan Car Tyre Pump, repaired- washer

There appeared to be room for a small washer to take up the excess space, so I fitted one I had lying around.

IMG_3597.JPG
FixItWorkshop, Worthing, May’17 AirMan Car Tyre Pump, repaired- pump now in line with washer

The washer, once fitted, allowed the flywheel/ toothed drive to sit ‘square’ in-line with the pump.

Once resembled, the pump ran freely and was ready to inflate, once more.

Cost of a new pump, circa £20.  Cost of the washer, circa 5p.

Intermittent Einhell E-BH 950 SDS drill

Poorly drill repaired at FixItWorkshop

The owner of this drill complained that it work perfectly one minute and then stopped the next.  It was making DIY a very slow process.

IMG_3505
FixItWorkshop, April’17, Worthing, Einhell E-BH 950 SDS drill repaired

As this was a cut-out problem rather than a slowing down issue, power problems were a likely suspect.

On test, the cable flex near the base of the handle seemed to be the issue as giving it a good wiggle seemed to reproduce the fault.

Opening up the drill (several self-tapping screws) revealed a fairly straightforward layout with cord, mechanical connector, smoothing circuit (mains splash) and switch.  Having suspected the culprit to be cable flex near the handle, I cut the cable down and re-made the connection, removing the suspect part of the cable.

IMG_3503
FixItWorkshop, April’17, connector shown
IMG_3502
FixItWorkshop, April’17, broken cable removed

Despite cutting the cable flex down by about 8″, the owner was pleased with this fix since no spare parts were required and no real issues will be noticed since it will be mainly used with an extension lead.