Inside The Real Repair Shop 2

Practical vacuum cleaner maintenance advice from the workshop!

I have 5 vacuum cleaners, each kept for specific tasks, as you can imagine.  No, seriously I love vacuum cleaners.  From friendly faced Henrys and Hettys to ‘frickin’ Sharks, I love ‘em all.  Why you ask? Well I guess that using a hoover is sheer joy to me.  You take your machine to a grubby area, run it around the floor, and you are rewarded with instant gratification! The carpet is returned to near pristine condition.  Better still, with many machines, you can see all the muck that was once on the carpet, swirling around in mesmerizing dust-storms, in the see-through debris collection bin!  Cosmic stuff.

Decent vacuum cleaners cost a few quid and far too many repairable machines end up at tips across the country, prematurely.

I suspect that many machines could be saved with basic skills. Most people could manage light servicing with basic tools and a small dusting of knowledge so here are some top tips to help you keep your hoover running well for longer.

Models vary, but you are likely to need the following: 

  • Big flat-head screwdriver
  • a cross-head screwdriver
  • damp cloth bowl of hot soapy suds

Before you start work on any appliance, always unplug from the mains. 

Brush heads: Upright vacuum cleaners probably have a rotating brush head. Remove any dog, cat, child hair, Lego etc from the brushes, especially the stuff stuck at the sides, where it can cause damage to things like bearings.  Use a knife or some old scissors to cut-away trapped hair etc.  This will improve performance and prevent damage. 

FixItWorkshop, Worthing, January’21, Dyson DC07 brush head- looking clean.

Filters:  Many vacuum cleaners have at least one, sometimes three filters to prevent dust entering back into the environment it was sucked-up from, preventing sneezes.  Usually all you need to do is see where the filters are located and to remove any retaining clips/covers.  Some machines use screws to hold the filters in-situ, so you’ll need to familiarise yourself with your instructions. 

If you’ve held on to your instructions, well done.  If you’re like most people and have chucked the instructions away, you might need to Google your model and download them. These filters need to be cleaned every three months in warm soapy water and left to dry for at least 24 hours or until bone dry.  Clean filters not only prevent dust build-up in the air, but are essential for the free flow of air into your machine and out again.

A blocked motor filter could cause overheating and damage to the motor bearings and brushes.  Suction can be reduced by a blocked cylinder filter. HEPA filters need to be replaced and can’t be cleaned, however eBay is awash with good quality, cheap alternative filters, so there’s no excuse for not lavishing your machine with some filter-love to let your machine breathe easy.

FixItWorkshop, Worthing, January’21, old and new filters.

Seals:  All vacuum cleaners rely on good seals between joints to ensure perfect performance.  Rubber and foam seals need to be cleaned regularly to prevent the build-up of dirt. Get a bowl of hot soapy water and an old cloth to clean up joints and seal-like surfaces, no special skills required.  Don’t scrub too hard as you might damage the smooth surfaces, just a gentle clean is all that’s needed.  Remember, dirty seals equal vacuum loss.

FixItWorkshop, Worthing, January’21, keep seals clean with a damp sponge or cloth.

Just a small tune-up in the way of basic servicing will mean that your trusty vacuum runs sweeter for longer, saving you time, money and valuable resources.  You’ll also bond with your machine, which is a good thing.

After all that cleaning, you’ve earned yourself a cup of tea. Time to put the kettle on, make a brew and grab a custard cream.

Check your plug! A simple Miele PowerLine Vacuum Cleaner repair

Mains plugs lead a hard life, make sure yours are safe. If they are damaged, replace!

Before and after…

A quick 15-minute job, with a satisfying result.

Sometimes, it’s not a complicated fault preventing an otherwise good machine from working.  It’s just a case of taking the plunge and getting stuck in as the owner of this vacuum cleaner had proved.

Make and model: Miele PowerLine Vacuum Cleaner

Fault reported: Not running/ occasional sparks(!)

Cost of replacement: About £139.99

Cost of parts: £0.00

Hours spent on repair: ¼

Tools needed: Cutters, screwdriver and soldering iron

Sundry items: Silicone spray, T-Cut

Repair difficulty: 1/10

Cups of tea: 1

Biscuits: 1 Ginger Nut

 

IMG_0300
FixItWorkshop, Worthing, November ’19, Miele S5211 Vacuum Cleaner.

Sometimes the simplest things are the best.  This machine had been working well when sparks began coming from the mains plug.  The owner had reacted quickly by turning off the power and then removing the plug from the wall socket.  Good job.

The owner then bought a new plug from a local hardware shop to replace the damaged (cracked) plastic plug fitted.  She then fitted the new plug to the vacuum cleaners’ flex but nothing happened when she switched it back on.  Frustrating!  It’s reassuring to hear that folk still bother to get screwdrivers out and attempt a repair.  It makes it all worthwhile.

When I saw the vacuum cleaner and heard the back story, I immediately inspected the plug wiring and spotted that a bit of insulation was still trapped on the live connecter, preventing the electrical connection.  30 seconds with a pair of cutters and a small flat blade screw driver and the machine was working again.

Me being me, I then decided to give the Miele’s plastic casing a quick polish with T-Cut and wax, to bring it up to the correct standard.

It made me think:  How often do people change plugs these days?  Not often.  So, if you’re wondering what the correct position of the wires should be, it’s this (UK specification).

Capture
FixItWorkshop, November’19, UK plug – not my image.

General hints

  • Make sure all screws are tight
  • Ensure the cable grip clamps the cable insulation
  • Don’t trap wires in between the casing

If in any doubt, consult a friendly shed-dweller or spanner spinner.